Iranian Journal of Materials Science and Engineering

---

In the present paper, the influence of cobalt additive on the sintering/infiltration behavior of W-Cu composite was studied. For this purpose, the mixed powders of tungsten and cobalt were compacted by CIP method and then sintered at 1450, 1550 and 1600 °C in a hydrogen atmosphere. The sintered specimens at 1550 °C were subsequently infiltrated with liquid copper at 1250 °C for 10, 60 and 120 min. The microstructure and composition of samples were evaluated using SEM, EDS as well as XRD techniques. The density of the sintered samples was measured by Archimedes method. Vickers indentation test was used to measurement hardness. It was found that sintering mechanism of tungsten powder depends on temperature and cobalt additive content. Also, the best infiltration behavior was observed in the samples with optimum cobalt value. In addition, it was found that the W-W contiguity as well as dihedral angle decreases as cobalt increases. Density and hardness of infiltrated specimens are attained 16.28-16.79 g.cm-3 and 220-251 VHN, respectively.

---

This paper reports the wear behavior of Cu, high Cu-Sn alloy, high Cu-Pb alloy and high Cu-Sn-Pb alloy under dry sliding at ambient conditions. These four materials were chosen for the wear resistance characterization of SnPb-solder affected old/scraped copper (high Cu-Sn-Pb alloy) to explore its reusing potentials. Wear tests were conducted using a pin-on-disk tribometer with the applied load of 20N for the sliding distance up to 2772 m at the sliding speed of 0.513 ms^-1. The applied load was also changed to observe its effect. The investigation reveals that the presence of a little amount of Sn increased the hardness and improved the wear resistance of Cu, while a similar amount of Pb in Cu reduced the hardness but improved the wear resistance. The general perception of ‘the harder the wear resistant’ was found to match partially with the results of Cu, Cu-Sn alloy and Cu-Sn-Pb alloy. Coefficient of friction (COF) values revealed non-linearly gradual increasing trends at the initial stage and after a certain sliding distance COF values of all four sample materials became almost steady. SnPb-solder affected Cu demonstrated its COF to be in between that of Cu-Pb alloy and Cu-Sn alloy with the maximum COF value of 0.533.

---

Copper oxide thin layers were elaborated using the sol-gel dip-coating. The thickness effect on morphological, structural, optical and electrical properties was studied. Copper chloride dihydrate was used as precursor and dissolved into methanol. The scanning electron microscopy analysis results showed that there is continuity in formation of the clusters and the nuclei with the increase of number of the dips. X-ray diffractogram showed that all the films are polycrystalline cupric oxide CuO phase with monoclinic structure with grain size in the range of 30.72 - 26.58 nm. The obtained films are clear blackin appearance, which are confirmed by the optical transmittance spectra. The optical band gap energies of the deposited films vary from 3.80 to 3.70 eV. The electrical conductivity of the films decreases from 1.90.10^-2 to 7.39.10^-3 (Ω.cm)^-1

---

The effect of the milling time & ageing on the hardness, density, and wear characteristics of Al 7150 alloy specimens made via powder metallurgy has been studied. The different constituents of Al 7150 alloy were processed in a planetary ball milling set up with a BPR of 10:1 for 5 hours, 10 hours, and 20 hours. At 400 °C, the milled powders were subsequently hot compacted in a punch die setup. The hot-pressed specimens were solutionized initially, then aged artificially at 115 °C for 3, 6, 12, 24, 30, 45, 60, and 96 hours. The relative density was inversely proportional to the milling time. Microhardness tests showed a maximum VHN of 255 was measured for the 24 h aged T6 specimens produced from 20 h milled powders whereas the non-aged specimens, made from unmilled 7150 alloy powders showed a VHN of 40. However the samples showed a decline in microhardness beyond 24 h of ageing. Under various conditions of sliding distance and loading conditions, the samples subjected to T6 aging showed a reduced volumetric wear rate indicating the beneficial effect of artificial aging up to 24 hours. The volumetric wear rate gradually declined for the samples aged beyond 24 hours of aging. The HRTEM studies revealed a high density of uniformly scattered (MgZn₂) precipitates in the base matrix, as well as (MgZn₂) phases precipitating along grain boundaries. The presence of such second phase precipitates in the matrix improved the wear characteristics of the alloy matrix. The results showed that optimization of process parameters such as milling time, ageing as well as reducing the particle size of the base powders, the hardness and wear behavior of Al 7150 alloy may be improved.

---

This contribution evaluates the influence of Cr doping on the ground state properties of SrTiO3 Perovskite using GGA-PBE approximation. Results of the simulated model infer agreement with the previously published literature. The modification of electronic structure and optical properties due to Cr3+ doping levels in SrTiO3 has been investigated. Structural parameters infer that Cr3+ doping alters the electronic structures of SrTiO3 by shifting the conduction band through lower energies for the Sr and Ti sites. Substituting Ti site by Cr3+ results the energy gap in being eliminated revealing a new electrical case of conducting material for the system. Furthermore, it has been noticed that Cr doping either at Sr or Ti positions could effectively develop the SrTiO3 dielectric constant properties. Consequently, Cr3+ is an effective dopant due to enhancing the optical absorption properties, thus opening up new prospects for optoelectronic applications.