Showing 177 results for Cr
S. Manafi, S. Joughehdoust,
Volume 17, Issue 2 (6-2020)
Abstract
In this research, calcium titanate (CaTiO3) hollow crystals have been successfully prepared via hydrothermal method. Titanium tetrachloride, calcium chloride dihydrate and potassium hydroxide were used as Ti, Ca and precipitating agent, respectively. The hydrothermal synthesis was performed at different temperatures and time durations. The negative amount of the Gibbs free energy shows the reactivity of the reaction at room temperature. Characterization of CaTiO3 was carried out using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD). The optimum condition for preparing CaTiO3 is the sample kept in an autoclave at 300 ℃ for 3 h that requires less energy and time which consists of a high degree of crystallinity. In this research, tetragonal CaTiO3 hollow crystals have been successfully prepared via hydrothermal method. TiCl4, CaCl2.2H2O, and KOH were used as Ti, Ca and precipitating agent, respectively. The hydrothermal synthesis was performed at different temperatures and time durations. Characterization of CaTiO3 was carried out using SEM, HRTEM, and XRD. The sample kept in the autoclave at 300 ℃ for 3 h well crystallized and required less energy and time for synthesis. The powder has a homogenous dispersity of crystals with the range of nanometer to micrometer sizes which makes it a good candidate as a photocatalyst material
S. Agbolaghi,
Volume 17, Issue 2 (6-2020)
Abstract
Confined and unconfined crystallizations of poly(3-hexylthiophene) (P3HT) were studied in the solution-grown supramolecules and melt-grown systems using a differential scanning calorimeter. The carbon nanotube (CNT) and reduced graphene oxide (rGO) and their functionalized (CNT-f-COOTh and rGO-f-TAA) and grafted (CNT-g-PDDT and rGO-g-PDDT) derivatives were employed to develop the samples. The absorbance, structure details via Scherrer formula, fusion enthalpy (ΔHm) and crystallinity (Xc) were measured in two distinct confined/unconfined crystallization environments. Although the functionalized-CNT/rGO precursors partially reduced the crystallite qualities with respect to the pristine CNT and rGO ones in the solution-grown supramolecules, they did not affect the structural properties in the melt-grown samples. Grafted carbonic materials could be considered as appropriate seeds for the arrangement of P3HTs in both solution and melt crystallizations. The best absorbances, larger and more compact crystals, and higher melting point, ΔHm, and Xc values were recorded for the pre-developed CNT-g-PDDT/P3HT stem-leaf (6.09–22.51 nm, 3.52–13.89 Å, 239.8 °C, 30.86 J/g and 83.40%) and rGO-g-PDDT/P3HT coarse-patched (5.96–20.76 nm, 3.57–13.95 Å, 237.6 °C, 29.13 J/g and 78.73%) supramolecules. Although the melt-grown CNT-g-PDDT/P3HT (201.4 °C, 215.3 °C, 16.22 J/g and 43.84%) and rGO-g-PDDT/P3HT (205.4 °C, 218.8 °C, 18.06 J/g and 48.81%) nanostructures were not as perfect as the respective solution-grown nano-hybrids, they were well-arranged with respect to the CNT/P3HT, CNT-f-COOTh/P3HT, rGO/P3HT and rGO-f-TAA/P3HT samples
Sa. Benkacem, K. Boudeghdegh, F. Zehani, Y. Belhocine,
Volume 17, Issue 2 (6-2020)
Abstract
This paper focuses on the effect of ZrSiO4/ZnO ratio on the properties of the glaze to be used on ceramic sanitary-ware. Structural and morphological characterization of these glazed ceramics were identified by XRD, SEM, FTIR and Raman Spectroscopy. Furthermore, thermal properties were determined by DTA and TG techniques. Besides, flexural strength, Vickers Microhardness, whiteness and chemical resistance were investigated experimentally. XRD analysis showed that the zircon and quartz were the crystalline phases, zircon was also precipitated into the glaze layer during firing. It was found that an increase of the ZrSiO4/ZnO ratio part weights from 3.85 to 67, causes an increase in the zircon crystallite particle size from 203.90 to 288.86 Å. From DTA, it was observed that by increasing ZrSiO4/ZnO ratio, the crystallization temperature of zircon decreases. The glaze exhibits the highest whiteness value when the ratio of ZrSiO4/ZnO becomes 12.60.
A. Beigei Kheradmand, S. Mirdamadi, S. Nategh,
Volume 17, Issue 3 (9-2020)
Abstract
In the present study, the effect of adding minor amounts of scandium and zirconium elements to the 7075 alloyon the re-crystallization behaviour of one aluminium alloy (7000 series) was investigated. For this purpose, two kinds of Al-Zn-Mg-Cu-Sc-Zr alloys with the same amount of Zr and different amount of Sc were prepared. Homogenization durations and temperatures of alloys after alloying were obtained by DSC analysis and optical microstructure observations. The results showed that the optimum homogenization temperatures for Al-Zn-Mg-Cu-0.05Sc-0.1Zr and Al-Zn-Mg-Cu-0.1Sc-0.1Zr alloys were 500
0C and 490
0C respectively, and the optimum duration for both alloys was 12hours. After homogenization of alloys, the re-crystallization behaviour of the alloys was investigated by Brinell hardness test. Obtained results showed that although the starting re-crystallization temperature for both alloys was similar in 2 hours, but it was 130°C for alloys with 30% forming, and 120°C for alloys with 50%forming and recrystallization temperature for Al-Zn-Mg-Cu-0.1Sc-0.1Zr alloy was 350
in 2 hours. Despite what was expected, the hardness of Al-Zn-Mg-Cu-0.05Sc-0.1
S. Mortezaei, H. Arabi, H. Seyedein, A. Momeny, M. Soltanalinezhad,
Volume 17, Issue 3 (9-2020)
Abstract
Dynamic Recrystallization (DRX) is one of the likely mechanisms for fine-graining in metals and alloys. The dynamic recrystallization (DRX) phenomena occurs in different thermo-mechanical processing (TMP) conditions for various metallic materials. DRX depends on various materials and thermo-mechanical parameters such as temperature, strain rate, strain, stress and initial microstructure. in the present study, the restoration mechanism of the 17-7PH stainless steel has been investigated using a hot compression test under different conditions of thermo-mechanical treatment. The microstructural characteristics and the behavior of the hot deformation of the under study steel are investigated using flow curves and microstructure images obtained from optical microscopy. The results show that the maximum and steady state stresses are significantly affected by the strain rate and the deformation temperature. So that, the flow stress increases with decrease in the deformation temperature and increase in the strain rate. Microstructural studies confirm the occurrence of DRX as a restoration mechanism in the microstructure for the two phases of austenite and ferrite.
N. Mohammed, H. F. Dagher,
Volume 17, Issue 3 (9-2020)
Abstract
Thin films of meta-cinnabar mercuric sulfide (β-HgS) nanoparticles (NPs) was prepared by pulsed laser ablation (PLA) utilizing a pellet of cinnabar mercuric sulfide (α-HgS) was immersed in distilled water (DW). Q-switched Nd:YAG laser of 1064 nm wavelengths with repetition rate (1hz) and fluency (1.5 J/cm2) applied for ablation. Structural, morphological and particle sizes of the β-HgS NPs are invastigated by analyzing XRD, AFM, SEM and TEM measurements. Their crystal structure is transformed from hexagonal (wurtzite) of the α-HgS target material to cubic (zinc blende) β-HgS NPs. The optical properties of the β-HgS NPs are measured by UV–visible spectrophotometer. The direct band gap is calculated to be (2.45eV) of small particles (4-6.2nm) moreover, the band gap value of smallest particles (1-4nm) is (3.47eV) according to the optical transmission spectra
R. Niazi, E. Tohidlou, H. Khosravi,
Volume 17, Issue 3 (9-2020)
Abstract
The effects of erbium (Er) addition at various weight percentages (0-0.6 wt.% at an interval of 0.2) on the microstructural characteristics, tensile response and
wear properties of as-cast Al-7.5Si-0.5Mg alloy were evaluated. The microstructure of samples was examined by X-ray diffraction, optical microscopy and scanning electron microscopy. The obtained results demonstrated that the incorporation of erbium obviously decreased the α-Al grain size and eutectic Si, and altered the Si morphology from plate to semi-globular. Further addition of erbium (> 0.2 wt.%) did not alter the eutectic morphology and size. Moreover, the Al
3Er phase was also observed in the eutectic region after modification. Out of the erbium contents used, 0.2 wt.% erbium showed the best influence on the tensile and wear properties. Compared with those of unmodified specimen, the values of ultimate tensile strength and elongation were enhanced by 31% and 39%, respectively with the introduction of 0.2 wt.% erbium. Additionally, a remarkable enhancement in the wear properties was observed with the addition of 0.2 wt.% erbium.
P. Shahsavari, B. Eftekhari Yekta, V. Marghussian,
Volume 17, Issue 3 (9-2020)
Abstract
Strong glass-ceramic foams with a compressive strength of 20 MPa were prepared by adding various amounts of Fe2O3 to a soda lime-based glass composition, and SiC as a foaming agent. The foams were prepared by firing the compacted samples in the range of 750–950°C for different soaking times. The crystallization behavior of the samples was investigated by Simultaneous Thermal Analysis (STA), Scanning Electron Microscope, and X-Ray Diffractometer (XRD). Based on the results, solid solutions of pyroxene groups were crystallized by the surface mechanism, between 730˚C and 900˚C during the firing of the specimens, and their amounts increases with increasing of the added iron oxide. Besides, we found that Fe2O3 neither acts as a nucleant for pyroxene nor as an oxidizer for SiC. The results also showed that the compressive strength as well as the crystallization behavior of the foams was influenced by the presence of the SiC particles.
M. Azarbarmas,
Volume 17, Issue 4 (12-2020)
Abstract
Mechanical properties of metals are substantially dependent on the microstructure, which can be controlled by thermo-mechanical parameters such as the temperature, strain and strain rate. Hence, understanding the microstructural evolution of alloys during the hot deformation is crucial for engineering the metal forming processes. The main objective of this work is to present an overview of Cellular Automaton (CA) modeling for predicting the microstructure of alloys during the dynamic recrystallization (DRX) phenomenon. In this review paper, first, overall descriptions about the DRX phenomenon and CA modeling were presented. Then, the CA modeling procedure was compared with similar methods. Meanwhile, related studies in the field of the DRX simulation by using the CA modeling were evaluated. Four main stages of the model were analyzed in terms of the “nucleation”, “growth”, “topological changes” and “texture evaluation” steps. Most important limitations including the calibration sensitivity, limitations in continuous DRX modeling, ignoring microstructural effects on the deformation behavior, limited applications and database as well as repeated results were discussed and then objective suggestions for the further development were provided. Finally, future prospects in CA modeling of DRX were presented in the last section.
E. Abbasi, K. Dehghani, T. Niendorf, S. V. Sajadifar,
Volume 17, Issue 4 (12-2020)
Abstract
The effect of cooling rate after annealing at 900 °C on the microstructure and hardness of high entropy alloys was investigated using two typical samples with the chemical composition of Co16Cr14.5Fe29Mn11.5Ni29 and Co11.5Cr7Fe27Mn27Ni27(Nb0.08C0.5) (at%). The microstructural characterisation and hardness measurements were carried out by optical microscopy, scanning electron microscopy, wavelength-dispersive X-ray spectroscopy, electron back scattered diffraction, X-ray diffraction technique and Vickers hardness testing. A face centred cubic crystal structure matrix was observed in both alloys before and after annealing and regardless of cooling conditions. SEM analyses revealed an extensive precipitation in Co11.5Cr7Fe27Mn27Ni27(Nb0.08C0.5) alloy after annealing. It was also found that air/furnace cooling can enhance grain growth-coarsening just in Co16Cr14.5Fe29Mn11.5Ni29. However, the hardness results generally showed insignificant hardness variations in both alloys after water-quenching, air-cooling and furnace-cooling. The results suggested that the hardness is mainly controlled by solid solution strengthening.
Zahra Rousta, Esmaeil Tohidlou, Hamed Khosravi,
Volume 18, Issue 1 (3-2021)
Abstract
This study deals with the effects of erbium (Er) addition on the microstructural evolution and tensile properties of Al-Mg2Si in-situ metal matrix composites. The morphology of primary Mg2Si and eutectic phases were observed in details using optical microscope and scanning electron microscopy (SEM). The results showed that the increase of Er content has a slight effect on the size and morphology of primary Mg2Si phases, but the eutectic structure evolves from the coarse structure into the fine one. Also, with Er addition the eutectic mixtures of Al and Mg2Si with fibrous morphology has been developed instead of the flake like Al-Mg2Si eutectic microstructure. Meanwhile, Al3Er phase was observed in the samples containing Er. The ultimate tensile strength (UTS) of the composite changes under the various content of Er. The maximum strength was found at the 0.6 wt% Er with the fine eutectic microstructure. The study of SEM micrographs from the fracture surface of composites revealed that Er addition changes the fracture mode from brittle to ductile one with fine dimples. The mechanism of microstructural evolution was discussed in details.
Reza Soleimani Gilakjani, Seyed Hossein Razavi, Masoumeh Seifollahi,
Volume 18, Issue 1 (3-2021)
Abstract
Niobium addition is an appropriate approach for improvement of superalloy’s operation. The purpose of this study is twofold: (1) to investigate on the η and γ/ phase precipitations along with (2) to identify the high-temperature tensile properties in A286 and Nb-A286, as a modified type. The heat treatment of both alloys was carried out in a two-stage aging procedure at 760°C for 16 h and 820°C for 2 to 30 hours, following characterized by optical and Scanning electron (SEM-EDS) microscopies, differential thermal analysis (DTA) and high temperature tensile tests. The results showed that niobium addition was increased the volume fraction of γ/ phase, from 10.7% to 12%, decreased its size, from 94 to 71 nm, and rising the γ/-dissolution temperature from 987°C to 1007°C. Moreover, the γ/ to η phase transformation was sluggishly occurred in Nb-A286 due to more stable of γ/ precipitations. Furthermore, the Nb-A286 alloy demonstrates higher mechanical properties than A286 one, approximately 100MPa improvement, which it was contributed to the much large volume fraction and finer size of more stabilized γ/ phase.
Jonas Fernando Macedo, Igor Alexandre Fioravante, Roberto Zenhei Nakazato, Heloisa Andréa Acciari, Eduardo Norberto Codaro,
Volume 18, Issue 1 (3-2021)
Abstract
As we all know, corrosion of pipelines by hydrogen sulfide is the most worrying factor in the production and transport of oil and gas. In this work the corrosion behavior of API 5L X70MS and X70MO low carbon steels in hydrogen sulfide environments was investigated. Hydrogen induced cracking and sulfide stress cracking tests were carried out according to NACE TM0177 standard. After testing, blisters and cracks were observed only in X70MO steel, probably due to its lower grain refinement and banded microstructure. Internal cracks seem to be initiated in elongated MnS inclusions. Corrosion process was studied by obtaining potentiodynamic polarization curves, which were registered after open circuit potential measurements, at room temperature. Both steels showed general corrosion in NACE 177A solutions, but the corrosion rate values in H2S-saturated solution were about an order of magnitude higher than those ones in deaerated solution. Hydrogen permeation w::as char::acterized in accordance with ASTM G148 standard. In deaerated H2SO4 solution, permeation measurements were similar for both steels. In H2S-saturated solution, X70 MO exhibited higher hydrogen oxidation current values than X70 MS. H2S seems to promote the reduction of protons and increase the concentration of hydrogen atoms in the solution/steel interface, favoring the diffusion process. As X70MO has a coarse microstructure, it offers more pathways for hydrogen diffusion.
Sedigeh Mohamadnejad Zanjani, Ali Basti, Reza Ansari,
Volume 18, Issue 2 (6-2021)
Abstract
Phenomenological methods are more diagnostic tools than a predictor, so multi-crystalline material approaches based on their microstructures have been proposed during the last years. The purpose of this research is to review methods taking into account the effect of microstructures and texture deformation on predicting the behavior of sheet metals. These methods can be categorized into six general groups: Taylor-type models, crystal plasticity finite element methods, strain gradient methods, methods that consider dislocations, self-consistent methods, methods based on fast Fourier transform. This paper attempts to explain and compare these methods that have been used to forecasting forming limits or stress-strain curves.
Namrata Saxena, Varshali Sharma, Ritu Sharma, Kamlesh Kumar Sharma, Kapil Kumar Jain,
Volume 18, Issue 2 (6-2021)
Abstract
The work reported in this paper was focused on the investigation of surface morphological, microstructural, and optical features of polycrystalline BaTiO3 thin film deposited on p-type Si < 100 > substrate using e-beam PVD (physical vapor deposition) technique. The influence of annealing over the surface morphology of the thin film was analyzed by X-ray diffraction, atomic force microscopy and scanning electron microscopy characterization methods. When the annealing temperature was increased from as-deposited to 800 °C there was a significant growth in the grain size from 28.407 nm to 37.89 nm. This granular growth of BaTiO3 made the thin film appropriate for nanoelectronic device applications. The roughness of the annealed film got increased from 31.5 nm to 52.8 nm with the annealing temperature. The optical bandgap was computed using Kubelka-Munk (KM) method which got reduced from 3.93 eV to 3.87 eV for the as-deposited to the 800 °C annealed film. The above reported properties made the annealed film suitable for optoelectronic applications. For polycrystalline BaTiO3 thin film the refractive index varied from 2.2 to 1.98 from 400 to 500 nm and it was 2.05 at 550 nm wavelength. The broad peaks in Raman spectra indicated the polycrystalline nature of the thin film. It had been also observed that with the annealing temperature the intensity of the Raman bands got increased. From these results, it was proved that annealing significantly improved the crystallinity, microstructural, surface morphological and optical features of the barium titanate thin film which made it suitable as sensors in biomedical applications as it is cost-effective, lead-free and environment friendly material.
Rahida Wati Sharudin, Nik Salwani Md Azmi, Muhammad Shafiq Mat Shayuti, Masahiro Ohshima,
Volume 18, Issue 2 (6-2021)
Abstract
The control of silicone rubber’s viscoelastic properties namely loss factor, storage and loss moduli during crosslinking are crucial as its malleable behaviour changes differently under different conditions and affecting the final product. Hence, it becomes the objective of this study to investigate the rheological behaviour of silicone rubber cured under different formulation ratios with platinum catalysts and triethylamine, methanol & ethanolamine solvent. Measurement was conducted for the silicone rubber to crosslinker ratios of 2.5:7.5, 5:5, 7.5:2.5 and 10:1 at different elevated temperatures, and for the silicone rubber with triethylamine, methanol and ethanolamine at different angular frequencies. While the crossover of storage and modulus curve which signifies a gel point was not observed at higher ratios of platinum used across the temperature range of 25 – 100°C, it was found at 89°C and 95°C with the formulation ratios of 10:1 and 7.5:2.5, respectively. On the other hand, the crossover point was observed for silicone rubber at 100 s-1 for triethylamine, 3 s-1 and 100 s-1 for methanol, and 70 s-1 alongside 290 s-1 for ethanolamine. The presence of gel point indicates that crosslinking of silicone rubber successfully took place and this study proves that controlling the crosslinking behaviour was possible.
Farid Lekmine, Hachemi Ben Temam, Elhachmi Temam,
Volume 18, Issue 3 (9-2021)
Abstract
Nickel phosphorus alloy coatings were prepared by electrodeposition route from sulfate electrolyte bath at various current densities. SEM studies reveal spherical grains covered the entire surface with uniform distribution. EDX results showed a linear increase of P content in the developed deposits with current density and therefore, enhancing the grains size and drop of the hardness values. XRD studies reveal monocrystalline orthorhombic alloys at a low amount of phosphorus (10.88 wt. %). Corrosion tests show that 1 A.dm-2 is the best applied current density giving the nobler Ecorr (-171.4 mV) and the lower icorr (4.64 µA/cm2).
Saeed G. Shabestari, Sahar Ashkvary, Farnaz Yavari,
Volume 18, Issue 3 (9-2021)
Abstract
The influence of melt superheating treatment on the solidification characteristics and microstructure of Al–20%Mg2Si in-situ composite has been investigated. The results revealed that melt superheating temperature has a significant effect on solidification parameters and morphology of primary Mg2Si particles. Solidification parameters acquired using cooling curve thermal analysis method, indicate that both nucleation temperature and nucleation undercooling of primary Mg2Si particles increase by increasing melt superheating temperature, while recalescence undercooling decrease under the same condition. Also, based on the microstructural evaluations, melt superheating treatment can refine primary Mg2Si particles and alter their morphology from dendritic shape to more spherical shape and the eutectic microstructure of a-Al + Mg2Si becomes finer and the distance between eutectic layers becomes smaller.
Hilal Acay, Ayfer Yıldırım, Ayşe Baran,
Volume 18, Issue 3 (9-2021)
Abstract
Gold nanoparticles (AuNP) were synthesized using edible mushroom Russula delica (RD) in this study. Possibilities to evaluate these synthesized nanoparticles (RD-AuNPs) as bioactive substances were investigated. Characterization of synthesized RD-AuNPswere characterized via UV-vis, XRD, FTIR, EDX. In spherical view, RD-AuNPs with a crystal size of 34.76 nm were synthesized. As a result, fungal systems used for nanomaterial biosynthesis as an effective alternative to chemical synthesis can be used in different biotechnological and medical applications. RD-AuNPs produced by green synthesis can be evaluated in this context.
Mitra Ghannadi, Hediye Hosseini, Bagher Mohammad Sadeghi, Bahman Mirzakhani, Mohammad Tahaaha Honaramooz,
Volume 18, Issue 3 (9-2021)
Abstract
The objective of the present paper is to investigate the effects of rapid heating and cryogenic cooling on on the microstructure and tensile properties of Al-Cu-Mg. The specimens were subjected to three heat treatment cycles in which the Infrared heating (IR) were used as the heating medium at the ageing stage, and the liquid nitrogen and water were used as the quenching mediums. The ageing temperature and time were 190⁰C and from 2 hours to 10 hours, respectively.The results indicated that by using IR at the ageing stage, the hardening rate enhanced because the rapid heating via this method leads to faster diffusion of the alloying elements. Moreover, the high density of nano-sized precipitates formed during ageingleads to higher strength and suitable ductility. Cryogenic treatment showed a negligible effect on both microstructure and tensile properties; however, it improved ductility. Overall, the combination of a high heating rate and cryogenic treatment led to the highest mechanical properties. SEM micrograph of the fracture surface of alloy demonstrated that in Cryogenic treatment+Artificial Ageing (CAA) condition, the surface had been fully covered by deep dimples in contrast to the Cryogenic treatment+Infrared Heating (CIR) and Water-Quench+ Infrared Heating (QIR) conditions which their dimples were shallow and also some facets were observed.
